Recent content by MortenB

  1. M

    Brinkmann Balance vs. J. Sikora Reference- Battle of the $50K Belt Drives

    A lot of the design from J. Sikora is based the combination of different metals with different properties for resonans damping, and Quite a few metals are involved. They seem to consider the combination of aluminium, steel, brass etc as their best sounding turntables. Expensive to manufacture...
  2. M

    EMT - JSD series Carts

    Cheap compared to a 1.675 euro rebuild..! I use this type of ‘’stylus guard’’
  3. M

    EMT - JSD series Carts

    My Italian is extremely rusty, as in non existing, but google translate helped me out. Thanks again for your advise, I much appreciate this and will try different aligments of the cartridge at some point when it’s broken in… Regarding the price I consider myself very, very lucky. I bought it...
  4. M

    EMT - JSD series Carts

    Just to support what’s being said about the JSD - Platinum being very sensitive to VTA, load etc… As mentioned above I started out with the cartridge seeing a load of around 295 ohm. Yesterday I decided to make a small change to get the load more in the middle of EMT’s recommended load on 200...
  5. M

    EMT - JSD series Carts

    Thank you for advise on different transformers. For now I have decided on the Lundahl LL-1931 transformers coupled in a 1:4 ratio. I will start by following your advise Massimo66 and put some hours on it to break in the cartridge and transformer, and then time will tell… For my Thöress - Phono...
  6. M

    EMT - JSD series Carts

    Thanks again, not to crazy priced. I might try one of those at some point..!
  7. M

    EMT - JSD series Carts

    Thanks again, I have learned something new today! They do not mention the transformer ratio, but one must assume it’s around 1:5..? Do you have any idea on the price level for these?
  8. M

    EMT - JSD series Carts

    @DasguteOhr, thank you for sharing the STX 20 / 21, I have never seen that before. As you say the 1.05mV is a bit problematic to combine with transformers. I also noticed, that EMT under Micha Huber now offer more ‘’normal’’ versions of the cartridges. Were I to order a new EMT cartridge, I...
  9. M

    EMT - JSD series Carts

    By my calculation the cartride is loaded at 296 ohm. When I have some more hours on the cartridge and SUT I will experiment with the loads. According to an experienced transformer designer I’m lucky to know, the parallel connection of the secondaries is a benefit, and the 1:4 ratio is perfect...
  10. M

    EMT - JSD series Carts

    I would think then, that the difference you heard was due to the change in load the cartridge ‘’see’’ when switching from 1:5 and 1:10. It also makes sense, that when not using load resistors, that you preferred 1:10, as this is closer to the 200 - 300 ohm load recommended by EMT. Here the...
  11. M

    EMT - JSD series Carts

    Thanks for the info on your experience. Did you change the load also when going from 1:5 or 1:10? Often the difference in sound is because the load the cartridge sees changes. In this case where I connect the two secondary windings in parallel this cuts the impedance of the seconday in half...
  12. M

    EMT - JSD series Carts

    I just bought a JSD - Platinum freshly rebuild at EMT after the young son of the first owner broke the cantilever. The seller learned, that he needs a cartridge with a stylus guard… My phonostage is the Thöress - Phono Enhancer, and the 1mV output from the JSD - Platinum is on the loud side for...
  13. M

    My personal journey to MY SONIC LAB

    I fully agree and I find Shaktis comparative reviews amongst the best sources for info on cartridges anywhere online. I learn more from these comparisons, than from individual reviews. And BTW, he does not sell My Sonic Lab, so in this case his review is actually competing with products he does...
  14. M

    I've been reading lots in the magazines about the J. Sikora tables - any actual owners here who care to share their thoughts?

    Thanks again, I much appreciate your inputs on SQ as this has been a bit of an unknown to me. Using different metals as resonance control is sort of a Sikora trademark, as you also know from the Reference where several different metals are used. From what I understand the best sounding Standard...
  15. M

    I've been reading lots in the magazines about the J. Sikora tables - any actual owners here who care to share their thoughts?

    Interesting and thank you for your post. You’re the first owner I have heard from who has experience with both the Standard MAX and the Reference. With the difference in price the Reference should be better on sound quality..! On the other hand I have hear dealers mention, that they are very...
See more

About us

  • What’s Best Forum is THE forum for high end audio, product reviews, advice and sharing experiences on the best of everything else. This is THE place where audiophiles and audio companies discuss vintage, contemporary and new audio products, music servers, music streamers, computer audio, digital-to-analog converters, turntables, phono stages, cartridges, reel-to-reel tape machines, speakers, headphones and tube and solid-state amplification. Founded in 2010 What’s Best Forum invites intelligent and courteous people of all interests and backgrounds to describe and discuss the best of everything. From beginners to life-long hobbyists to industry professionals, we enjoy learning about new things and meeting new people, and participating in spirited debates.

Quick Navigation

Home Forums Contact us

User Menu

Login
Steve Williams
Site Founder | Site Owner | Administrator
Ron Resnick
Site Co-Owner | Administrator
Julian (The Fixer)
Website Build | Marketing Managersing
Top Bottom