Hi Mick,I am looking for subwoofer recommendations for my TAD CE1 TX speakers. My room size is 28 x 22 with 15' ceiling.
All help appreciated.
Mick
I haven’t tried using a crossover but when I was interested in buying the JL crossover, several people said they had one and didn’t like how it affected the upper pass. I was wondering if making a passive speaker cable with hard wired roll off filter just for woofer section might be more transparent? Meaning bi-wire.I would argue that the insertion loss (impact on ultimate sonic transparency) of an active line level crossover like the JL Audio CR-1 is absolutely negligible compared to the huge benefits of relieving the "satellite" speakers and their driving amplifiers of the lowest octave (via the CR-1's high pass filter at 24 dB/octave). Under these conditions, I would expect significantly greater mid-bass power and midrange purity plus a smoother blend between satellite and subs.
Maybe your personal experience is different.
I expect that the passive components required for such a high pass filter (at around 80-120 Hz) would be extremely large, expensive and with tremendous potential to colour the sound, at least compared to the active solution. Otherwise, why do people change small value capacitors in preamps in pursuit of sonic differences.I haven’t tried using a crossover but when I was interested in buying the JL crossover, several people said they had one and didn’t like how it affected the upper pass. I was wondering if making a passive speaker cable with hard wired roll off filter just for woofer section might be more transparent? Meaning bi-wire.
Thank you for your recommendation.I have a similar size room /ceiling height and use a pair of Velodyne dd10 plus subs with my CR1’s to very good effect, with the Servo set at its highest. I have the subs on 22” sistrum stands and sitting very far from any walls or corners for very tight bass with no overhang. I run my TAD’s full range as I’ve heard people say even the very good JL crossover will have a detrimental impact on sound.
While Uber expensive, I’d love to hear the new Wilson benesch infrasonic generators and hope to hear them soon, but at $30k US each……
Below is my Velodyne setup.
View attachment 130349
The Wilson Benesch infrasonic generator is on my list as is the Magico subwoofers. I was told by a few people that I trust that the WB is the one that would pair the best with my speakersI have a similar size room /ceiling height and use a pair of Velodyne dd10 plus subs with my CR1’s to very good effect, with the Servo set at its highest. I have the subs on 22” sistrum stands and sitting very far from any walls or corners for very tight bass with no overhang. I run my TAD’s full range as I’ve heard people say even the very good JL crossover will have a detrimental impact on sound.
While Uber expensive, I’d love to hear the new Wilson benesch infrasonic generators and hope to hear them soon, but at $30k US each……
Below is my Velodyne setup.
View attachment 130349
How do you find the bass on your Reference TAD speakers? I am considering upgrading to the TAD-R1TX but I really love the mids and trebles on my CE1 TX and do not want to give that up.@luthcol, the only issue with the WB is the cost. 2 subs is always better than 1 as far as smoothing out and distributing bass. The new IGx would be $60k for the pair. The previous generation, could be powered with a more powerful amp than they sold with it. Not sure how much an improvement the new generation makes. Unfortunately I’ve never heard either, but hope to soon.
@Young Skywalker I’d want to roll off the bass to my tad woofers much lower, around 60hz as I’m not sure how well my subs would play much higher. I’ll start asking around about a passive solution to experiment with. I’ve also thought about sealing the port in my tad as that would limit the bass extension. Anyone done this?
I’m not sure why the mid/treble would be of any concern moving to the reference series. But only you can decide if the upgrade is for you after listening.How do you find the bass on your Reference TAD speakers? I am considering upgrading to the TAD-R1TX but I really love the mids and trebles on my CE1 TX and do not want to give that up.