SET amp owners thread

  • Like
Reactions: Campo007
What did you Biamp with? How did you attach the amps. Vertical or horizontal.
They look similar to mine. I have 2x15 and a 10" coax.
I use the Ayon Spark V (18w SET) for the full range (103db sensitivity), which i let roll off naturally. I run the W15 (twin coil) woofers (93db sensitivity) with two Yamaha PX5 (set in parallel mode so both coils are seeing a separate amp and rolling off at 150hz, 12db).

Initially i had my heart set on a pair of Pure Audio Project Trio with coax, but at $16k AUD plus taxes, these came in at half the price.
 
Last edited:
I use the Ayon Spark V (18w SET) for the full range (103db sensitivity), which i let roll off naturally. I run the W15 (twin coil) woofers (93db sensitivity) with two Yamaha PX5 (set in parallel mode so both coils are seeing a separate amp and rolling off at 150hz, 12db).

Initially i had my heart set on a pair of Pure Audio Project Trio with coax, but at $16AUD plus taxes, these came in at half the price.
I thought about doing similar. A pro audio PA amp with active crossover to run the woofer. Why Yamaha. I heard their amps are not as good as they use to be. Are you using an older nodel. I think mine cross around 400 to 600 hertz. Thats a problem as most crossovers don't do that.
 
  • Like
Reactions: Campo007
I use the Ayon Spark V (18w SET) for the full range (103db sensitivity), which i let roll off naturally
I think you'll find that if you can keep the bass out of the SET it will sound better (smoother, more detailed) right away.

SETs have real troubles with bass because the output transformer would be enormous (small refrigerator size) if it were to actually have enough inductance to support the bass frequencies and doing so would mean it has no high frequency bandwidth. It doesn't due to a 'cut core' which is used to prevent saturation distortion in the core (magnetic laminations) of the output transformer. So lower distortion is traded off for limited low frequency capability due to low inductance at low frequencies.

Since inductance is what makes transformers work, the load impedance to which the output tube is subjected gets very low (approaches the DC resistance of the wire in the primary winding, which is only a few hundred Ohms) and isn't the sort of thing the tube should endure. So limiting the bass response is helpful. It will also help you have more power available to the overall result is lower distortion at nearly any volume at which you can play the system right now.

There are very simple ways to do this- by using a small coupling caps that limits the bass at the input of the amp, or by replacing an existing cap inside the amp to achieve the same result.
 
I thought about doing similar. A pro audio PA amp with active crossover to run the woofer. Why Yamaha. I heard their amps are not as good as they use to be. Are you using an older nodel. I think mine cross around 400 to 600 hertz. Thats a problem as most crossovers don't do that.
Marchand can do whatever you need and do it with tubes.
 
I use the Ayon Spark V (18w SET) for the full range (103db sensitivity), which i let roll off naturally. I run the W15 (twin coil) woofers (93db sensitivity) with two Yamaha PX5 (set in parallel mode so both coils are seeing a separate amp and rolling off at 150hz, 12db).

Initially i had my heart set on a pair of Pure Audio Project Trio with coax, but at $16AUD plus taxes, these came in at half the price.
I have a Spark as well in my biamped second system. I use it on the bass/mid but in my system that is a 99dB driver from Supravox in a TQWT cabinet. The tweeters are compression drivers driven by 300B monos.
 
  • Like
Reactions: Campo007
Interesting! What is its efficiency and are you preventing bass from reaching the amp that drives the Platinum?
I use the Ayon Spark V (18w SET) for the full range (103db sensitivity), which i let roll off naturally. I run the W15 (twin coil) woofers (93db sensitivity) with two Yamaha PX5 (set in parallel mode so both coils are seeing a separate amp and rolling off at 150hz, 12db).
I thought about doing similar. A pro audio PA amp with active crossover to run the woofer. Why Yamaha. I heard their amps are not as good as they use to be. Are you using an older nodel. I think mine cross around 400 to 600 hertz. Thats a problem as most crossovers don't do that.
Yes, it's a new one. I bought the Yamaha as recommended from a friend who A/B'd it with the Crown and other amps in the class. He said the Yamaha was easily the best of the bunch. But because it's crossing over at 150Hz, i'm not hearing anything negative. Rather the contrary. I've never experienced bass like this in my room. Even compare to when i had my JBL 4365 with SVS SB16 sub. Sure the sub went deeper, but that system never moved air like this.
 
I use the Ayon Spark V (18w SET) for the full range (103db sensitivity), which i let roll off naturally. I run the W15 (twin coil) woofers (93db sensitivity) with two Yamaha PX5 (set in parallel mode so both coils are seeing a separate amp and rolling off at 150hz, 12db).

Yes, it's a new one. I bought the Yamaha as recommended from a friend who A/B'd it with the Crown and other amps in the class. He said the Yamaha was easily the best of the bunch. But because it's crossing over at 150Hz, i'm not hearing anything negative. Rather the contrary. I've never experienced bass like this in my room. Even compare to when i had my JBL 4365 with SVS SB16 sub. Sure the sub went deeper, but that system never moved air like this.
Can you set the crossover to cut off at 600 hertz and role of at 24db? As in, I want the bass up to 600 on the woofers.
 
When you want work with yamaha amp max (150hz/12db cut) to activated your woofer.
You need to add a good midrange driver or a good coax driver 10" or bigger that easy works down under 100hz. Exsample
I have test alot in last 8 years..to optimize
 
I use the Ayon Spark V (18w SET) for the full range (103db sensitivity), which i let roll off naturally. I run the W15 (twin coil) woofers (93db sensitivity) with two Yamaha PX5 (set in parallel mode so both coils are seeing a separate amp and rolling off at 150hz, 12db).

Yes, it's a new one. I bought the Yamaha as recommended from a friend who A/B'd it with the Crown and other amps in the class. He said the Yamaha was easily the best of the bunch. But because it's crossing over at 150Hz, i'm not hearing anything negative. Rather the contrary. I've never experienced bass like this in my room. Even compare to when i had my JBL 4365 with SVS SB16 sub. Sure the sub went deeper, but that system never moved air like this.
Crowns tend to be horrible IMO especially for bass ..
 

About us

  • What’s Best Forum is THE forum for high end audio, product reviews, advice and sharing experiences on the best of everything else. This is THE place where audiophiles and audio companies discuss vintage, contemporary and new audio products, music servers, music streamers, computer audio, digital-to-analog converters, turntables, phono stages, cartridges, reel-to-reel tape machines, speakers, headphones and tube and solid-state amplification. Founded in 2010 What’s Best Forum invites intelligent and courteous people of all interests and backgrounds to describe and discuss the best of everything. From beginners to life-long hobbyists to industry professionals, we enjoy learning about new things and meeting new people, and participating in spirited debates.

Quick Navigation

User Menu

Steve Williams
Site Founder | Site Owner | Administrator
Ron Resnick
Site Owner | Administrator
Julian (The Fixer)
Website Build | Marketing Managersing