Lampizator Valve / Tube Rolling Review Thread

dminches

Well-Known Member
Oct 22, 2011
3,409
2,794
1,410
I have a metal base Amperex and metal base Mullard. There were the “sought” after GZ34 for a while. I should try it in my Big 7.
 

Sablon Audio

Industry Expert, VIP Donor
May 22, 2015
1,612
1,484
553
David, you should try it and form your own opinion. Blue and I experimented with this ages ago in my GG but found it lacking compared to the regular EML5u4g. Others have however felt differently and you might do also.
 

Zero000

Well-Known Member
Jul 28, 2014
2,985
1,139
478
Nervous times on the tube tester.

RD27AS first. What we're looking for is 7ma/V for a new valve.

Sold by cipsnaj eBay rating 995 sales at 100% feedback. He declared these to test at 75%.

What did we get?

5.2 and 5.3 ma/V. Cipsnaj is an excellent seller. As bang on 75% as you could expect and it shows common agreement between testers.

It also shows that the guy who restored this tester knew what he was doing.

IMG_20200418_200402.jpg IMG_20200418_200416.jpg IMG_20200418_200852.jpg IMG_20200418_201531.jpg
 
  • Like
Reactions: Golum

Zero000

Well-Known Member
Jul 28, 2014
2,985
1,139
478
Now here's the PX25 test.

This just freaked me out. The Osram came in with flying colours at 7.2. The Marconi came in at 3.3.

WTF? Only two sections of the filament appeared to be lit. Tapped the valve. A blue spark emitted from the far left hanger. Tapped again. And again. More blue sparks.

Then... hey presto it sprang to life. All four sections lit as you can see. Phew! Close call.

Then perhaps unsurprisingly it measured 6.6 ma/V.

I am pretty happy with that TBH and it is better as a pair than a number of triodes I have bought new. Really.

30 minutes in the tester and it is still fine. Let's hope it stays that way.?

IMG_20200418_202645.jpg IMG_20200418_202733.jpg IMG_20200418_204834.jpg
 

Attachments

  • IMG_20200418_204915.jpg
    IMG_20200418_204915.jpg
    744.4 KB · Views: 9
  • Like
Reactions: iain and Golum

findog

Well-Known Member
Apr 29, 2019
74
58
105
57
www.tinyurl.com
Yes...he corrected it. I have seen those on Ebay for up to $600each. I still have one. Gave one to Yoda and Al years ago. Dunno if they still have them.

His looks like a black base however. Tubedepot as the black base for $199.
 

dminches

Well-Known Member
Oct 22, 2011
3,409
2,794
1,410
His looks like a black base however. Tubedepot as the black base for $199.

If you look closely you can see it is a metal base. Plus, I have a lot of black base GZ34s and none have that short of a base.
 

findog

Well-Known Member
Apr 29, 2019
74
58
105
57
www.tinyurl.com
If you look closely you can see it is a metal base. Plus, I have a lot of black base GZ34s and none have that short of a base.

Is there a major difference in quality sound as there is in price?
 

dminches

Well-Known Member
Oct 22, 2011
3,409
2,794
1,410
Is there a major difference in quality sound as there is in price?

That is in the ears of the beholder. If you ask me I don’t think the sound difference justifies the price differences. There are some really good plastic base GZ34s that sound great.
 
  • Like
Reactions: findog

findog

Well-Known Member
Apr 29, 2019
74
58
105
57
www.tinyurl.com
Concerning rectifiers I have been playing with three today for fun: CV717 5R4G NOS Haltron Twin Disc Getter, standard KR rectifier that came with the unit, and Acme 274b, top 10%. And they all sound really good. Very difficult to tell the difference between them. If I had to pick, the NOS Haltron has more visceral impact today. Tomorrow...well...
 

Tim F

Well-Known Member
Jun 11, 2018
125
43
113
The GZ34 is a metal base Mullard made in Holland, series 2. Of course everyone has an opinion, that's what makes this hobby fun. Tried to describe the sound, only you will know if it suits your system and sound preference. So many factors!

User211 glad you got it working! Looks amazing. By the way if anyone has rectifiers they want to sell PM me. I'm enjoying playing with lots at the moment :) (UK based)
 

Tim F

Well-Known Member
Jun 11, 2018
125
43
113
Concerning rectifiers I have been playing with three today for fun: CV717 5R4G NOS Haltron Twin Disc Getter, standard KR rectifier that came with the unit, and Acme 274b, top 10%. And they all sound really good. Very difficult to tell the difference between them. If I had to pick, the NOS Haltron has more visceral impact today. Tomorrow...well...

What are you running them with? I tried the Haltron / FIVRE with the 242s and it didn't do much.
 

findog

Well-Known Member
Apr 29, 2019
74
58
105
57
www.tinyurl.com
What are you running them with? I tried the Haltron / FIVRE with the 242s and it didn't do much.
With Gold Lion Genalex KT77s.
 

Zero000

Well-Known Member
Jul 28, 2014
2,985
1,139
478
Lampi is back. And it is running very quietly indeed - no more tranny hum. It now has more heater selections than a Pacific I believe.

I am thinking of a hardwood top with larger holes as last night two new additions simply wouldn't fit in the rectifier holes and I had to remove the top to try them. The same is true for the triode sockets where the bases are too recessed for an AD1 adapter.

The Rod Coleman mod is very effective and very gentle on the valves on power up. Caveat is you must power down when rolling but in truth I always did that anyway.

Here's a shot showing RD27AS against an Amperex 211.

Note the RD is on a B4 to UX4 socket. So it is a bit of a misleading shot.

So Lampi spec now relative to an original early B7:

Dueland copper foil 0.47uF (in original) output caps via one set of WBTs.
Jupiter copper foil 2.2 uF via another set of WBTs.
Audio Note's finest silver tants on the RCA jacks.
Audio Note silver UX4 sockets.
Custom built Toroidy transformer - the best they do potted in an extremely nice chrome cover. Cost? £140.
Mil spec heater selection selection switch which is superbly satisfyingly clunky!:)
Rod Coleman heater regulation.
Huge Rod Coleman heatsink. I noticed this does get quite warm running the RDs.
Original Big 7 DAC board.
Active triode loading via 6N6P.
Rectifier modded from 6X5 to 5U4G.

I want to wait for the second set of 100% RDs before I comment on this new Tesla acquisition.

This DAC does sound better than it did. Hardly surprising given the poor state of the power supply before it got sorted.


IMG_20200420_135711.jpg
 

Attachments

  • IMG_20200420_135011.jpg
    IMG_20200420_135011.jpg
    811.4 KB · Views: 194
  • IMG_20200420_135711.jpg
    IMG_20200420_135711.jpg
    690.8 KB · Views: 2
Last edited:

wisnon

Well-Known Member
Dec 12, 2011
3,525
635
1,200
What are you running them with? I tried the Haltron / FIVRE with the 242s and it didn't do much.
Jason has a TRP...different circuit, so cant compare to the GG/Pac circuit in terms of recti pairings.
 
  • Like
Reactions: findog

adamaley

Well-Known Member
Apr 15, 2016
581
541
228
Minnetonka, MN
Lampi is back. And it is running very quietly indeed - no more tranny hum. It now has more heater selections than a Pacific I believe.

I am thinking of a hardwood top with larger holes as last night two new additions simply wouldn't fit in the rectifier holes and I had to remove the top to try them. The same is true for the triode sockets where the bases are too recessed for an AD1 adapter.

The Rod Coleman mod is very effective and very gentle on the valves on power up. Caveat is you must power down when rolling but in truth I always did that anyway.

Here's a shot showing RD27AS against an Amperex 211.

Note the RD is on a B4 to UX4 socket. So it is a bit of a misleading shot.

So Lampi spec now relative to an original early B7:

Dueland copper foil 0.47uF (in original) output caps via one set of WBTs.
Jupiter copper foil 2.2 uF via another set of WBTs.
Audio Note's finest silver tants on the RCA jacks.
Audio Note silver UX4 sockets.
Custom built Toroidy transformer - the best they do potted in an extremely nice chrome cover. Cost? £140.
Mil spec heater selection selection switch which is superbly satisfyingly clunky!:)
Rod Coleman heater regulation.
Huge Rod Coleman heatsink. I noticed this does get quite warm running the RDs.
Original Big 7 DAC board.
Active triode loading via 6N6P.
Rectifier modded from 6X5 to 5U4G.

I want to wait for the second set of 100% RDs before I comment on this new Tesla acquisition.

This DAC does sound better than it did. Hardly surprising given the poor state of the power supply before it got sorted.


View attachment 64280
Glad you're back in action. I can't imagine how difficult the wait must have been.
 
  • Like
Reactions: Zero000

About us

  • What’s Best Forum is THE forum for high end audio, product reviews, advice and sharing experiences on the best of everything else. This is THE place where audiophiles and audio companies discuss vintage, contemporary and new audio products, music servers, music streamers, computer audio, digital-to-analog converters, turntables, phono stages, cartridges, reel-to-reel tape machines, speakers, headphones and tube and solid-state amplification. Founded in 2010 What’s Best Forum invites intelligent and courteous people of all interests and backgrounds to describe and discuss the best of everything. From beginners to life-long hobbyists to industry professionals, we enjoy learning about new things and meeting new people, and participating in spirited debates.

Quick Navigation

User Menu

Steve Williams
Site Founder | Site Owner | Administrator
Ron Resnick
Site Co-Owner | Administrator
Julian (The Fixer)
Website Build | Marketing Managersing