No, my amp is an Anthem P5 (5 channel amp) which uses two power cords (120V maximum of 1800 watts per leg). My runs will be for 20 amp circuits with each circuit running a maximum of 15 feet wire from a breaker to outlet (8 circuits from a sub panel). The wires are cryo treated Romex 12AWG.
Electrical Power - Dedicated Runs
- Thread starter Audire
- Start date
I’ll s the main breaker after the utility meter
the terminal block in black is used to make more then one tap
Looks like two taps are being used
Not sure if this is directly on point, @Audire, but when I moved to Austin I had what I would call an electrical "subsystem" installed for the hi-fi-- 60 amps coming off the main service panel to a secondary panel, which then ran 4 gauge into a 10kVa iso transformer. The output of the iso transformer was also 4 gauge and ran up to the second floor- a junction box was used but ultimately another "local" service panel was installed for the system where the electricians ran 4x 10 gauge dedicated lines. I never looked to see what fed that "local" service panel-- would 4 gauge normally fit or would the electricians have made the conversion from 4 to 10 at the last junction box?
In any case, it all sounded good if a little bright at first, but the system wasn't fully dialed in at this stage. The work was done by a commercial electrical company here that did large institutional, city and other far bigger projects than mine.
In any case, it all sounded good if a little bright at first, but the system wasn't fully dialed in at this stage. The work was done by a commercial electrical company here that did large institutional, city and other far bigger projects than mine.
Do you have any pics of the service entrance cable shown under the meter
It’s a black cable
The pic I’m looking for is what’s connected to that cable from the utility power
Specifically is it 3 wires or just 2 wires
Very smart. I did the same back in 2007 when preparing my new listening room. Did it help? No clue as this was a new room. The system had been down for 5 or 6 months so no way to confirm. But based on all my previous experiences with cryo-treating everything I could get my hands on electrical-wise, I've no doubt it didn't hurt.
Only problem was at that time I was only familiar with the more popular and restricted performance flavor of cryo-treating via the inferior vapor method and it wasn't until maybe 2013 that I was introduced to the sonically superior full-immersion method. As one expert told me, the difference is like eating half-baked cookies vs fully baked cookies and so it seemed performance-wise.
By 2006 I was having all my electrical wires and objects double-cryo'ed, including the 2007 Romex in my new room for even greater performance than the single-treated vapor method. But even the double-cryo'ed vapor method is sonically inferior to a single cryo-treatment via the full-immersion method.
A 75M roll of #12/2 NMD90 wire is $262.00 I can only imagine what a custom roll of Cryo treated wire would cost.
I guess it's all relative as I know some who spend many thousands more on a component whose sonic benefits are less than a handful of simple electrical objects cryo-treated via the full immersion method.
Back in 2007, my cryo'ing vendor in the mid-west (I'm west coast) purchased two rolls of 12g and 14g at 250ft per roll at his local hardware store and then double-cryo'ed and shipped to me for a total cost of about $600. Chump change really considering what it might bring to the mix.
Especially since it has to do with improving general electric current / input signal flow - which is really the only thing we care about regarding our playback systems, right? It's all 100% electric current / input signal flow and the quality thereof, isn't it? All the way from the power plant up to and including the speakers 'voice coils? Ok, 95% electrical if your source is analog.
IOW, every time somebody spends resources on genuine electrical improvements of any sort, all the angels of heaven rejoice... I mean, some might call call that performing proper due diligence.
Last edited:
Similar threads
